제퍼넷 로고

NASA, 우주 발사 시스템의 핵심 단계를 고체 로켓 부스터에 추가

시간

The 188,000-pound core stage for NASA’s Space Launch System is lowered between two solid rocket boosters Saturday, June 12, inside the Vehicle Assembly Building at the Kennedy Space Center in Florida. Credit: NASA/Cory Huston

The core stage for NASA’s first Space Launch System, the heavy-lift rocket designed to carry astronauts back to the moon, has been installed between two solid-fueled boosters on a mobile launch platform at the Kennedy Space Center for an unpiloted lunar test flight.

The 212-foot-tall (65-meter) orange core stage was raised vertical inside the Vehicle Assembly Building on June 11. A 325-ton crane hoisted the rocket several hundred feet above the floor of the huge assembly building June 12, then transferred the stage from the structure’s middle passageway, or transfer aisle, into an adjacent high bay.

The final stage of the around-the-clock, multi-day operation was to carefully lower the empty core stage in between the Space Launch System’s twin solid rocket boosters, which are already loaded with pre-packed solid propellants.

A NASA spokesperson said “soft mate” between the core stage and solid rocket boosters, longer versions of the solid-fueled motors used on the space shuttle, was completed in High Bay 3 of the Vehicle Assembly Building around 10 p.m. EDT June 12 (0200 GMT June 13).

Officials declared “hard mate” complete at 7 a.m. EDT (1100 GMT) on Sunday, June 13, when technicians completed structural connections at attach points at the forward and aft ends of the core stage, which weighs about 94 tons (85 metric tons) empty.

With the rocket components firmly mated, the crane disconnected from the core stage, leaving the two 177-foot-tall (54-meter) solid rocket boosters to carry the full weight of the rocket. The SLS main stage is suspended between the Northrop Grumman-made boosters, which are stacked on mounting pins on the mobile launch platform.

Unlike the space shuttle, there are no hold-down bolts connecting the solid rocket boosters to the mobile launch platform, which was designed specifically for the Space Launch System.

Four support posts, fitted with strain gauges to measure loads during stacking, rollout, and launch, serve as structural mounting points for each booster on the deck of the mobile platform.

The stacking of the core stage begins a process that NASA officials say should culminate in a fully-assembled Space Launch System and Orion spacecraft as soon as August. If everything goes on a schedule, a major “if” for a brand new rocket with a history of delays, NASA could move the 322-foot-tall (98-meter) rocket to pad 39B on top of one its giant Apollo-era crawler-transporters in September or October for a mock countdown and fueling test.

NASA는 1 월 말에 달 주변의 비 조종 시험 비행에서 SLS와 오리온 승무원 캡슐을 발사하기를 희망합니다. Artemis 2로 알려진이 임무는 2023 주 이상 지속되며 다음 SLS / Orion 임무 인 Artemis XNUMX가 XNUMX 년에 XNUMX 인승 승무원을 달에 태울 수있는 길을 닦을 것입니다.

2020 년대 후반의 아르테미스 임무는 상업적으로 개발 된 달 착륙선을 사용하여 달의 남극 근처에 우주 비행사를 착륙시킬 것입니다. XNUMX 월에 NASA는 대부분의 민간 자금으로 개발중인 재사용 가능한 무거운 리프트 로켓 인 SpaceX의 Starship의 변형을 선택하여 첫 번째 Artemis 승무원을 달에 착륙 시켰습니다.

그러나 NASA는 정부 소유의 우주 발사 시스템 로켓과 오리온 캡슐을 지구와 달 근처를 왕복 비행하는 데 사용할 계획이며, 우주 비행사는 우주 비행사가 우주 비행선과 같은 달 착륙선으로 이동하여 표면으로 하강합니다. .

The SLS core stage is lowered between two solid rocket boosters inside the Vehicle Assembly Building. Credit: NASA/Cory Huston

During launch, the core stage’s Aerojet Rocketdyne RS-25 engines and twin solid rocket boosters will generate 8.8 million pounds of thrust. It can send about 59,500 pounds (27 metric tons) of payload to the moon, more than any rocket operating today.

The ground crew inside the VAB rehearsed the lift and mate procedures in 2019 with a pathfinder structure built to mimic the weight and size of the SLS core stage. Before the SLS boosters were stacked a few months ago, the last time the VAB cranes lifted real rocket hardware in preparation for launch was before the final space shuttle mission in 2011.

미시시피의 스테니스 우주 센터에서 NASA 바지선을 타고 해상 여행을 마치고 로켓이 케네디의 차량 조립 건물로 굴러 들어간 지 약 25 주 후에 SLS 코어 스테이지가 들어 올려졌습니다. Stennis의 지상 승무원은 전체 발사 프로필을 시뮬레이션하기 위해 XNUMX 월에 XNUMX 분 이상 로켓의 RS-XNUMX 엔진 XNUMX 개를 시험 발사했습니다.

코어 스테이지가 XNUMX 월 말 플로리다에 도착한 이후 NASA와 로켓의 주 계약자 인 Boeing 팀은 Stennis에서 XNUMX 분 동안 시험 발사하는 동안 손상된 오렌지색 폼 단열재 수십 영역을 수리했습니다. 그들은 또한 올해 초 열화 테스트에서 불에 탄 로켓의 엔진 섹션 바닥에있는 코르크 단열재를 만졌다.

이 폼은 메인 스테이지의 극저온 추진제 탱크 내부의 온도를 조절하는 데 도움이됩니다.이 탱크에는 화씨 영하 730,000도 (섭씨 영하 423도)에 저장된 253 갤런 이상의 액체 수소와 섭씨 영하 298도 (섭씨 영하 183도)의 액체 산소가 저장됩니다.

엔지니어들은 또한 로켓 외부에서 수리가 필요한 몇 가지 센서를 확인했습니다. 테스트 발사 중에 로켓의 성능과 환경이 분리 된 데이터를 수집하도록 설계된 500 개 이상의 센서 중 일부입니다.

그리고 지상 승무원은 코어 스테이지의 외부를 따라 선형 모양의 충전물을 설치했습니다. 혐의는 비행 종료 시스템의 일부로, 로켓이 코스를 벗어나 대중을 위협하면 로켓을 파괴합니다.

With the core stage in place, the pace of stacking will be be “fairly quick,” said Cliff Lanham, senior vehicle operations manager for NASA’s exploration ground systems program.

Next will be the Launch Vehicle Stage Adapter, or LVSA, the interstage structure that will connect the main stage with the rocket’s upper stage.

The LVSA is scheduled to be installed on top of the core stage this week.

Then the Interim Cryogenic Propulsion System, or ICPS, will be added to the Space Launch System as soon next week in High Bay 3. The hydrogen-fueled upper stage is derived from the second stage of United Launch Alliance’s Delta 4-Heavy rocket.

This illustration shows the components of the Space Launch System’s Block 1 configuration, which is the version scheduled to fly on the rocket’s first mission, designated Exploration Mission-1. Credit: NASA

상위 단계는 현재 Kennedy의 Multi-Payload Processing Facility 내에서 출시 될 준비가되어 있습니다. High Bay 3의 팀이 준비되면 ICPS는 우주선을 타고 VAB까지 몇 마일을 타고 우주 발사 시스템 위에 올라갑니다.

“It’s a pretty aggressive stacking sequence that we’ll be following, all in an effort to get us ready and get the umbilicals mated so we can get into our power up and get into our real big test, which will be our umbilical retract test,” Lanham said in a recent interview.

상부 스테이지가 설치되면 지상 팀이 Orion 캡슐을 연결하도록 설계된 또 다른 어댑터를 들어 올립니다. 그런 다음 구조가 로켓 위에 올라가 오리온 우주선의 무게를 시뮬레이션합니다.

이는 이동식 발사 플랫폼의 타워와 로켓 사이를 달리는 추진제 라인, 유체 연결 및 기타 엄 빌리 컬이 이륙 할 때 안전하게 해제 및 후퇴 할 수 있는지 확인하기위한 테스트 단계를 설정합니다.

그런 다음 팀은 XNUMX 월에 완전 스택 형 발사체의 구조 공명 테스트 또는 모달 테스트로 이동합니다. 이 작업이 완료되면 팀은 발사 중단 시스템과 이미 통합 될 실제 Orion 우주선을 VAB로 이동하여 XNUMX 월 초에 발생할 수있는 이벤트 인 우주 발사 시스템 상단에 부착합니다. Lanham 말했다.

NASA가 웨트 드레스 리허설이라고 부르는 연습 카운트 다운 후 SLS와 오리온 우주선은 최종 폐쇄, 검사 및 군수 연결을 위해 차량 조립 건물로 돌아갑니다.

다음 번에 로켓이 39B 패드로 발사 될 때는 발사 XNUMX 일 전쯤이 될 것이라고 Lanham은 말했다.

“앞으로 도전에 직면 할 것입니다. “우리는 허리케인 시즌으로 향하고 있습니다. 그것이 어떻게 진행되는지 볼 것입니다. 처음으로이 작업을 수행했기 때문에 문제가 발생할 수 있지만 연말까지이 기능을 출시하기 위해 절대적으로 노력하고 있습니다. "

이메일 저자.

Twitter에서 Stephen Clark을 팔로우하십시오. 안녕하세요..

코인 스마트. 유로파 최고의 비트 코인-보르 스
Source: https://spaceflightnow.com/2021/06/16/nasa-bolts-space-launch-system-core-stage-to-solid-rocket-boosters/

spot_img

최신 인텔리전스

spot_img

우리와 함께 채팅

안녕하세요! 어떻게 도와 드릴까요?